| width | 100% |
|---|
| titleColor | white |
|---|---|
| titleBGColor | #5ba612 |
| title | RapidConnect v3.5.0 |
Release Notes
MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):
- CSB04PA10-CHP-N
- CSB04PA10-PIN-X
- CSB04PA10-RFC-N
- CSB04PA10-USB-N
- CSB04PA11-CHP-D
- CSB04PA11-PIN-X
- CSB04PA11-RFC-D
- CSB04PA11-USB-N
MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):
- GWY20-4-8-N
- EmberZNet Stack Port from v6.5.0 to v6.6.2
- OTA Client Download Policy Request/Response/Write Command (PH: 0x0B, SH: 0x27/0x28/0x29)
Ported Commissioning logic to use Network Steering rather than Form/Join Logic to be in line with ZB3.0 standards updates.
RapidConnect Serial Frame 0x01 0x01 (Form Network Command) is superseded by 0x01 0x31 (Network Formation Command). MMB recommends using the Network Formation Command to comply with ZB3.0 requirements
- RapidConnect Serial Frame 0x01 0x00 (Join Network Command) is superseded by 0x01 0x30 (Network Steering Command), in order to comply with ZB3.0 requirements. Network Steering prompts the device to automatically scan and attempt to join a network, first by Install Code, then using the well-known link key to attempt to join a Centralized Network, and finally attempting to join a Distributed network.
- Zigbee Router no longer perform RejoinRequest upon power cycle. Also, it will not perform TCLK update.
- Finding and Binding Support.
- Clusters must be categorized by Type1/2 and application/utility
- Update TC Install Code commissioning Process
- Scene Server Cluster revision update
- On/Off Server Cluster revision update
- Level Control Server Cluster revision update
- Network Commissioning: ZR shall not trigger a TC rejoin procedure after a power cycle
Downloads
- Commissioning Cluster Support has now been deprecated.
- EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 RFD to a coordinator
- This issue is under investigation by SiLabs
| Warning | ||
|---|---|---|
| ||
As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field to this release. If you would like to upgrade hardware running pre-3.4.x firmware, please consult with MMB support. |
Files
MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)
Enterprise 2.7 Gateway (GWY20-4-8-N)
Serial Protocol Specification
You can find our RapidConnect Serial Protocol v3.5.0 here.
| titleColor | white |
|---|---|
| titleBGColor | #00517f |
| title | RapidConnect v3.4.7 |
Release Notes
MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):
- CSB04PA10-CHP-N
- CSB04PA10-PIN-X
- CSB04PA10-RFC-N
- CSB04PA10-USB-N
- CSB04PA11-CHP-D
- CSB04PA11-PIN-X
- CSB04PA11-RFC-D
- CSB04PA11-USB-N
MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):
- GWY20-4-8-N
- Green Power Proxy Support
- Network Key Response command now masked for read-protected devices
- Renegade Bootloader 1.0.12 compatibility
- RAPCZ-1132
- 2nd Join by install code fails on a RC3 coordinator's network
- RAPCZ-1115
- Time Sever Master Bit cannot be set to 0
- RAPCZ-1508
- Time Server Cluster: Time status attribute is marked as reportable but should be RW
- RAPCZ-1047
- CN-NSA-TC-02: Network steering – looping behaviour failure
- RAPCZ-1545
- CN-NSA-TC-02: Network Steering>Cannot leave network when it fails to join at step 3
- RAPCZ-1449
- IAS Zone Cluster (0x500): Leaving a Network Does Not "Un-enroll" A Device
- RAPCZ-1549
- Join By Install Code: Coordinator Broadcasts Leave Request When Opening or Closing Permit Join
- RAPCZ-1582
- DUT(End Device) not responding to Read Attribute command 10 minutes after rejoining
- RAPCZ-1527
- Incorrect initial currentLevel at power up
- RAPCZ-1309: Basic Cluster: ZCL Version Attribute (0000) Reads Incorrectly
- EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 RFD to a coordinator
- This issue is under investigation by SiLabs
| Warning | ||
|---|---|---|
| ||
As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field to this release. If you would like to upgrade hardware running pre-3.4.x firmware, please consult with MMB support. |
Files
MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)
Enterprise 2.7 Gateway (GWY20-4-8-N)
Serial Protocol Specification
You can find our RapidConnect Serial Protocol v3.4 here.
| titleColor | white |
|---|---|
| titleBGColor | #00517f |
| title | RapidConnect v3.4.0 |
Release Notes
MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):
- CSB04PA10-CHP-N
- CSB04PA10-PIN-X
- CSB04PA10-RFC-N
- CSB04PA10-USB-N
- CSB04PA11-CHP-D
- CSB04PA11-PIN-X
- CSB04PA11-RFC-D
- CSB04PA11-USB-N
MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):
- GWY20-4-8-N
- RAPCZ-1339: Bootloader Access Frame
- New command frame added to provide Host access to the rescue bootloader
- RAPCZ-1258: RapidConnect Unable To Use JoinNetwork Frame to Join On Channel 26
- Joining issue on Channel 26 resolved
- RAPCZ-1309: Basic Cluster: ZCL Version Attribute (0000) Reads Incorrectly
- RAPCZ-1338: Read attribute response reaches payload length limit
- EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 Reduced Function Devices to a coordinator
- This issue is under investigation by SiLabs
- EmberZNet Stack Change: default End Device Timeout Value changed from 5 minutes to 256 minutes. This causes a delay in rejoining for HA 1.2 End Devices after they lose communication with a RapidConnect-based parent. This change was made in the stack, to align with R21 Zigbee Specifications
| Warning | ||
|---|---|---|
| ||
As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field. If you would like to upgrade existing hardware, please consult with MMB support. |
Files
MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)
Enterprise 2.7 Gateway (GWY20-4-8-N)
Serial Protocol Specification
You can find our RapidConnect Serial Protocol v3.4 here.
| titleColor | white |
|---|---|
| titleBGColor | #00517f |
| title | RapidConnect v3.1.1 |
Release Notes
- BSB03PA1x modules
- Z357PA4x modules
- New serial frames to enable configuration of Serial Outgoing Delay and Serial Retry Delay
- New serial frames to enable devices configured as a Coordinator to send Many-to-One Route Request (MTORR) messages at configurable intervals
- Fixes related to error reporting when Invalid Values are specified in various serial frames
- Fixes related to ZDO Announce and Request Key messages not being sent during joining
- Request Key messages: a device configured as a coordinator will ignore Request Key messages from a joining device if the messages are being delivered via a router
- This issue is understood to be rooted in the EmberZNet r21 stacks and is resolved in EmberZNet 6.3.x+
ZDO Send Broadcast: setting destination address to 0x00 doesn't set network destination address to 0xFFFF
- ZCL message encryption: after commissioning a Zigbee 3.0 device to a RapidConnect-based coordinator via Install Code, ZCL messages encrypted with with APS are being sent using an incorrect link key
- This firmware does not function correctly when configured as a Reduced Function Device.
Files
EFR32MG1 Solution (BSB03PA1x modules):
EM357 Solution (Z357PA4x modules):
Serial Protocol Specification
You can find our RapidConnect Serial Protocol v3.0 here.
| titleColor | white |
|---|---|
| titleBGColor | #00517f |
| title | RapidConnect v3.0.8 |
Release Notes:
- BSB03PA1x modules
- Z357PA4x modules
- Various stability improvements and fixes in the serial interface
- RF Output Power Correction
- It was observed that the application was not correctly configuring RF output power for operation on the BSB03PA10 module. This issue has been corrected in this release
- Currently supporting standalone (as opposed to application) bootloader
- OTA Client functionality not supported
- OTA Server functionality supported
Files:
EFR32MG1 Solution (BSB03PA1x modules):
EM357 Solution (Z357PA4x modules):
Serial Protocol Specification:
You can find our RapidConnect Serial Protocol v3.0 here.
| titleColor | white |
|---|---|
| titleBGColor | #00517f |
| title | RapidConnect v3.0.1 |
Release Notes:
- BSB03PA1x modules
- Z357PA4x modules
This is the first release of RapidConnect 3 for the BSB03PA1x modules (based on the Silicon Labs EFR32MG SoC) and Z357PAx modules (based on Silicon Labs EM357 SoC).
General Serial Interface Updates
- Module Info Response: Hardware Type enumerations modified to include 0x04 = EFR32MG1B232F256GM32
- Module Info Response: Bootloader Type enumerations modified to include 0x02 = Gecko Standalone Bootloader
Zigbee 3.0 Serial Interface Updates
- Trust Center Security Policy Write
- Trust Center Security Policy Request
- Trust Center Security Policy Response
- Trust Center Key Exchange Status Update
- Trust Center Removed Device Notification
- Trust Center Install Code Add
- Trust Center Install Code Request
- Trust Center Install Code Response
- Clear Trust Center Install Codes
- Trust Center Install Code Max Count Request
- Trust Center Install Code Max Count Response
Please refer to the RapidConnect Serial Protocol Frame Payload Definitions and the associated Usage Guidelines to learn more about these features.
- Standalone Bootloader & OTA Client
- Currently supporting standalone (as opposed to application) bootloader
- OTA Server functionality supported
- OTA Server functionality supported
- Green Power Support
- Green Power as a Proxy not supported (required for zb 3.0 compliance)
- Basic Cluster Attributes
- Still under investigation is a possible issue with local attribute writes to the Basic cluster, which require a reset of the device
- For the time being it is advised that Basic cluster attributes not be adjusted locally
Files:
EFR32MG1 Solution (BSB03PA1x modules):
EM357 Solution (Z357PA4x modules):
Serial Protocol Specification:
You can find our RapidConnect Serial Protocol v3.0 here.and Documentation
| Child pages (Children Display) |
|---|
Note: see the License Agreements page for the terms and conditions that apply to the use of MMB's RapidConnect products.
| Style |
|---|
{style}
.wiki-content h1 {
font-family: 'Helvetica Neue', sans-serif; font-size: 30px; font-weight: bold; color: #20b6e1; letter-spacing: 1px; line-height: 1; text-align: left;
#border-bottom: 1px solid #98bddd !important;
}
.wiki-content h2 {
font-family: 'Helvetica Neue', sans-serif; font-size: 20px; font-weight: normal; color: #00517f; letter-spacing: 1px; line-height: 1; text-align: left;
}
.wiki-content h3 {
font-family: 'Helvetica Neue', sans-serif; font-size: 15px; font-weight: bold; color: #00517f; letter-spacing: 1px; line-height: 1; text-align: left;
}
.wiki-content h4 {
font-family: 'Helvetica Neue', sans-serif; font-size: 15px; font-weight: normal; font-style:italic; color:#00517f; letter-spacing: 1px; line-height: 1; text-align: left;
}
#title-text{
font-family: 'Helvetica Neue', sans-serif; font-size: 40px; font-weight: 500; letter-spacing: 1px; line-height: 1; text-align: left;
}
.panel, #content .panel {
-moz-border-radius: 5px;
-webkit-border-radius: 5px;
border-radius: 5px;
}
.panel .panelHeader {
text-align: left;
color: #FFFFFF;
line-height: 1em;
padding: 10px 10px 5px;
margin-bottom: 0;
background-color: #00517f;
-moz-border-radius-topleft: 5px;
-moz-border-radius-topright: 5px;
-webkit-border-top-right-radius: 5px;
-webkit-border-top-left-radius: 5px;
border-top-right-radius: 5px;
border-top-left-radius: 5px;
}
{style}
|