Page Comparison

Panel

titleColor	white
borderWidth	2
titleBGColor	#5ba612
title	Firmware

Column

width	100%

Anchor

	RapidHA 1.7.5 .7 Downloads
	RapidHA 1.7.5 .7 Downloads

Expand

title	Version 1.7.5.7

Panel

titleColor	white
titleBGColor	#5ba612
title	1.5.7

Release Notes:

New Features

None

Bug Fixes
RapidHA 1.7 includes an expansion of the serial interface to application sleepy functionality. New sleep control frames under the Utility command group (PH: 0x55) provide the user with a wake-up handshaking scheme, as well as total and accurate control of application sleep cycles.

- [RHA-837] - RF Output Power and Channel Agility
  - All previous outstanding issues with RF Output Power have been resolved
  - When moving channels, the application will now apply the appropriate RF Output Power when scanning on the new channel

None
Known Issues	None

Files:

OTA Upgrade Firmware Image	rapidha-1.7.5

.7

-prod.ota
Serial Upgrade Firmware Image	rapidha-1.7.5

.7

-prod.mbl

Expand

title	Version 1.5.6

Panel

titleColor	white
titleBGColor	#5ba612
title	1.5.6

Release Notes:

New Features	None
Bug Fixes	[RHA-831] - OTA Adaptation for Daintree ControlScope Networks Implemented functionality to ensure correct operation of OTA upgrades on both standard HA 1.2 and Daintree ControlScope networks [RHA-847] - Attribute Reporting Behaving Incorrectly when Manufacturing Bit Enabled Per summary, corrected an issue where incoming Attribute Reports with the Manufacturing Bit enabled in Frame Control were rejected by the application with a default response
Known Issues	[RHA-837] - RF Output Power and Channel Agility Though the more critical issue of the application transmitting at maximum output during the Scan/Join cycle has been resolved (see Bug Fixes) there remains a secondary issue: The application will always apply the RF Output Power of the first channel the application joined to This implies that when moving to a new network (i.e. in pursuit of the coordinator) the application will apply the same RF Output Power when transmitting on the new channel This issue is minor, but we would caution that users should avoid operating the application on Channel 26 where possible

Files:

This release has been retired in favour of RapidHA v1.5.7 and is no longer supported

Expand

title	Version 1.5.3

[RHA-837] - RF Output Power

It was determined that regardless of the RF Output Power configuration applied at manufacturing time, the application would transmit at maximum output during the Scan/Join cycle

The application would then apply the expected RF Output Power once joined to the network

This issue has since been corrected, with the RF Output Power being applied during the Scan/Join cycle as expected
[RHA-837] - RF Output Power and Channel Agility

Panel

titleColor	white
titleBGColor	#5ba612
title	1.5.3

Release Notes:

New Features

- [RHA-796] - Application Version Request
  - Application now includes facilities for querying the Virtual Host application version
  - New frames under Utility command group (PH 0x55):
  - Application Version Count Request (0x06) (H > M)
  - Application Version Count Response (0x07) (M > H)
  - Application Version Request (0x08) (H > M)
  - Application Version Response (0x09) (M > H)
- [RHA-805] - Incoming Attribute Report Passthrough
- - Application now includes facilities for enabling passthrough of incoming Attribute Reports to the Host
  - New frame under ZigBee Configuration Support command group (PH 0x03):
  - - Attribute Report Passthrough Control (SH 0x26) (H > M)

Bug Fixes

Known Issues

Though the more critical issue of the application transmitting at maximum output during the Scan/Join cycle has been resolved (see Bug Fixes) there remains a secondary issue:
The application will always apply the RF Output Power of the first channel the application joined to
This implies that when moving to a new network (i.e. in pursuit of the coordinator) the application will apply the same RF Output Power when transmitting on the new channel
This issue is minor, but we would caution that users should avoid operating the application on Channel 26 where possible