Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 53 Next »

RapidConnect v3.5.0

Release Notes

Silicon Labs Stack VersionEmberZNet 6.6.2
Compatible Hardware SKUs

MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):

  • CSB04PA10-CHP-N
  • CSB04PA10-PIN-X
  • CSB04PA10-RFC-N
  • CSB04PA10-USB-N
  • CSB04PA11-CHP-D
  • CSB04PA11-PIN-X
  • CSB04PA11-RFC-D
  • CSB04PA11-USB-N

MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):

  • GWY20-4-8-N
New Features
  • EmberZNet Stack Port from v6.5.0 to v6.6.2
  • OTA Client Download Policy Request/Response/Write Command (PH: 0x0B, SH: 0x27/0x28/0x29)

  • Ported Commissioning logic to use Network Steering rather than Form/Join Logic to be in line with ZB3.0 standards updates.

  • Finding and Binding Support.
  • Clusters must be categorized by Type1/2 and application/utility
  • Update TC Install Code commissioning Process
  • Scene Server Cluster revision update
  • On/Off Server Cluster revision update
  • Level Control Server Cluster revision update
  • Network Commissioning: ZR shall not trigger a TC rejoin procedure after a power cycle
Bug Fixes
  • ZCL Send Multicast/Broadcast: Cluster not found when sending ZCL general command without client cluster
  • LC-TC-02S: Occasionally failing on step 11c
  • Sleep Control Stay Awake Duration Write frame not retaining values
  • Network Commissioning: Enterprise 2.7 can only join up to 3 devices by install code
  • Condor without flash firmware upgrade in fast mode is not fast
  • mmbSendIeeeAddrRequest using incorrect ZDO sequence number
  • PH:0x05 SH:0x30 Read Attribute Request, PH:0x05 SH:0x32 Write Attribute Request sent from incorrect source endpoint for green power
  • Poll Control Cluster Client now supported.
  • Set Up Reporting Rawframe (PH:05, SH:09) Not Working as Specified on Confluence Frame Payload Definitions
  • Better recovery mechanism for incompatible bootloader
  • Coordinator opens permit join incorrectly
  • Race condition in network engine on network join
  • Condor SED fast polling at 1 second instead of 0.5 second
  • Dev key RapidConnect v3.4.7, v3.4.8 missing on Potemkin
  • Client Clusters support attribute 0xFFFD
  • DUT Router: failed at step 12 for FB-PRE-TC-02 (ZR)
  • LC-TC-02S: failing on step 9c and 10c
  • Default reporting implemented on Thermostat and Illum Measurement Server Cluster
  • Network Commissioning: Permit join not reset when devices leaves network
  • OTA Upgrade and Serial Upgrade on Legacy Devices Causes Module to Reset before Upgrade Completely Downloads
Deprecated
  • Commissioning Cluster Support has now been deprecated.
Known Issues
  • EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 RFD to a coordinator
    • This issue is under investigation by SiLabs
Special Notes

Warning!

As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field to this release. 

If you would like to upgrade  hardware running pre-3.4.x firmware, please consult with MMB support. 

Files

MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)

OTA Upgrade Firmware ImageEFR32Condor-3.5.0-signed-external-combined-prod.ota
Serial Upgrade Firmware ImageEFR32Condor-3.5.0-signed-external-combined-prod.gbl

Enterprise 2.7 Gateway (GWY20-4-8-N)

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware ImageEFR32Condor-3.5.0-signed-external-prod.gbl

Serial Protocol Specification

You can find our RapidConnect Serial Protocol v3.5.0 here.


RapidConnect v3.4.7

Release Notes

Silicon Labs Stack VersionEmberZNet 6.5.0
Compatible Hardware SKUs

MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):

  • CSB04PA10-CHP-N
  • CSB04PA10-PIN-X
  • CSB04PA10-RFC-N
  • CSB04PA10-USB-N
  • CSB04PA11-CHP-D
  • CSB04PA11-PIN-X
  • CSB04PA11-RFC-D
  • CSB04PA11-USB-N

MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):

  • GWY20-4-8-N
New Features
  • Green Power Proxy Support
  • Network Key Response command now masked for read-protected devices
  • Renegade Bootloader 1.0.12 compatibility
Bug Fixes
  • RAPCZ-1132
    • 2nd Join by install code fails on a RC3 coordinator's network
  • RAPCZ-1115
    • Time Sever Master Bit cannot be set to 0
  • RAPCZ-1508
    • Time Server Cluster: Time status attribute is marked as reportable but should be RW
  • RAPCZ-1047
    • CN-NSA-TC-02: Network steering – looping behaviour failure
  • RAPCZ-1545
    • CN-NSA-TC-02: Network Steering>Cannot leave network when it fails to join at step 3
  • RAPCZ-1449
    • IAS Zone Cluster (0x500): Leaving a Network Does Not "Un-enroll" A Device
  • RAPCZ-1549
    • Join By Install Code: Coordinator Broadcasts Leave Request When Opening or Closing Permit Join
  • RAPCZ-1582
    • DUT(End Device) not responding to Read Attribute command 10 minutes after rejoining
  • RAPCZ-1527
    • Incorrect initial currentLevel at power up
Known Issues
  • RAPCZ-1309: Basic Cluster: ZCL Version Attribute (0000) Reads Incorrectly
  • EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 RFD to a coordinator
    • This issue is under investigation by SiLabs
Special Notes

Warning!

As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field to this release. 

If you would like to upgrade  hardware running pre-3.4.x firmware, please consult with MMB support. 

Files

MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)

OTA Upgrade Firmware ImageEFR32Condor-3.4.7-signed-external-combined-prod.ota
Serial Upgrade Firmware ImageEFR32Condor-3.4.7-signed-external-combined-prod.gbl

Enterprise 2.7 Gateway (GWY20-4-8-N)

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware ImageEFR32Condor-3.4.7-signed-external-prod.gbl

Serial Protocol Specification

You can find our RapidConnect Serial Protocol v3.4 here.

RapidConnect v3.4.0

Release Notes

Silicon Labs Stack VersionEmberZNet 6.5.0 (Silicon Labs Release Notes available here)
Compatible Hardware SKUs

MMB Condor Modules & USB Sticks (operating SiLabs EFR32MG13):

  • CSB04PA10-CHP-N
  • CSB04PA10-PIN-X
  • CSB04PA10-RFC-N
  • CSB04PA10-USB-N
  • CSB04PA11-CHP-D
  • CSB04PA11-PIN-X
  • CSB04PA11-RFC-D
  • CSB04PA11-USB-N

MMB Enterprise Gateway 2.7 (operating SiLabs EFR32MG13):

  • GWY20-4-8-N
New Features
  • RAPCZ-1339: Bootloader Access Frame
    • New command frame added to provide Host access to the rescue bootloader
Bug Fixes
  • RAPCZ-1258: RapidConnect Unable To Use JoinNetwork Frame to Join On Channel 26
    • Joining issue on Channel 26 resolved
Known Issues
  • RAPCZ-1309: Basic Cluster: ZCL Version Attribute (0000) Reads Incorrectly
  • RAPCZ-1338: Read attribute response reaches payload length limit
  • EmberZNet Stack Bug: Cannot join more than 5 ZB3.0 Reduced Function Devices to a coordinator
    • This issue is under investigation by SiLabs
  • EmberZNet Stack Change: default End Device Timeout Value changed from 5 minutes to 256 minutes. This causes a delay in rejoining for HA 1.2 End Devices after they lose communication with a RapidConnect-based parent. This change was made in the stack, to align with R21 Zigbee Specifications
  •  
Special Notes

Warning!

As of RapidConnect 3.4.0, firmware images have been encrypted with an updated bootloader security key. Devices operating releases prior to 3.4.0 (e.g. 3.3.x and below) may not be serially or OTA upgraded in the field. 

If you would like to upgrade existing hardware, please consult with MMB support. 

Files

MMB Condor Modules & USB Sticks (CSB04PA10 / CSB04PA11)

OTA Upgrade Firmware ImageEFR32Condor-3.4.0-signed-external-prod.ota
Serial Upgrade Firmware ImageEFR32Condor-3.4.0-signed-external-prod.gbl


Enterprise 2.7 Gateway (GWY20-4-8-N)

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware ImageEFR32Condor-3.4.0-signed-external-prod.gbl

Serial Protocol Specification

You can find our RapidConnect Serial Protocol v3.4 here.

RapidConnect v3.1.1

Release Notes

Silicon Labs Stack VersionEmberZNet 5.10.1 (Silicon Labs Release Notes available here)
Compatible Hardware SKUs
  • BSB03PA1x modules
  • Z357PA4x modules
New Features
  • New serial frames to enable configuration of Serial Outgoing Delay and Serial Retry Delay
  • New serial frames to enable devices configured as a Coordinator to send Many-to-One Route Request (MTORR) messages at configurable intervals
Bug Fixes
  • Fixes related to error reporting when Invalid Values are specified in various serial frames
  • Fixes related to ZDO Announce and Request Key messages not being sent during joining
Known Issues
  • Request Key messages: a device configured as a coordinator will ignore Request Key messages from a joining device if the messages are being delivered via a router
    • This issue is understood to be rooted in the EmberZNet r21 stacks and is resolved in EmberZNet 6.3.x+

  • ZDO Send Broadcast: setting destination address to 0x00 doesn't set network destination address to 0xFFFF

  • ZCL message encryption: after commissioning a Zigbee 3.0 device to a RapidConnect-based coordinator via Install Code, ZCL messages encrypted with with APS are being sent using an incorrect link key
  • This firmware does not function correctly when configured as a Reduced Function Device.

Files

EFR32MG1 Solution (BSB03PA1x modules):

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware Image

EFR32Cycloid-3.1.1-prod.gbl

EM357 Solution (Z357PA4x modules):

OTA Upgrade Firmware Image

EM357-3.1.1-prod.ota


Serial Upgrade Firmware Image

EM357-3.1.1-prod.mbl

Serial Protocol Specification

You can find our RapidConnect Serial Protocol v3.0 here.

RapidConnect v3.0.8

Release Notes:

Silicon Labs Stack VersionEmberZNet v5.10.1 (Silicon Labs Release Notes available here)
Compatible Hardware SKUs
  • BSB03PA1x modules
  • Z357PA4x modules
New FeaturesN/A
Bug Fixes
  • Various stability improvements and fixes in the serial interface
  • RF Output Power Correction
    • It was observed that the application was not correctly configuring RF output power for operation on the BSB03PA10 module. This issue has been corrected in this release
Known Issues
  • Standalone Bootloader & OTA Client
    • Currently supporting standalone (as opposed to application) bootloader
    • OTA Client functionality not supported
      • OTA Server functionality supported
  • Green Power Support
    • Green Power as a Proxy not supported (required for Zigbee 3.0 compliance)

Files:

EFR32MG1 Solution (BSB03PA1x modules):

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware Image

RapidConnect_3_0_8.gbl

EM357 Solution (Z357PA4x modules):

OTA Upgrade Firmware ImageRapidConnect_3_0_8.ota
Serial Upgrade Firmware ImageRapidConnect_3_0_8.mbl

Serial Protocol Specification:

You can find our RapidConnect Serial Protocol v3.0 here.


RapidConnect v3.0.1

Release Notes:

Silicon Labs Stack VersionEmberZNet v5.10.1
Compatible Hardware SKUs
  • BSB03PA1x modules
  • Z357PA4x modules
New Features

This is the first release of RapidConnect 3 for the BSB03PA1x modules (based on the Silicon Labs EFR32MG SoC) and Z357PAx modules (based on Silicon Labs EM357 SoC).

General Serial Interface Updates

  • Module Info Response: Hardware Type enumerations modified to include 0x04 = EFR32MG1B232F256GM32
  • Module Info Response: Bootloader Type enumerations modified to include 0x02 = Gecko Standalone Bootloader

Zigbee 3.0 Serial Interface Updates

  • Trust Center Security Policy Write
  • Trust Center Security Policy Request
  • Trust Center Security Policy Response
  • Trust Center Key Exchange Status Update
  • Trust Center Removed Device Notification
  • Trust Center Install Code Add
  • Trust Center Install Code Request
  • Trust Center Install Code Response
  • Clear Trust Center Install Codes
  • Trust Center Install Code Max Count Request
  • Trust Center Install Code Max Count Response

Please refer to the RapidConnect Serial Protocol Frame Payload Definitions and the associated Usage Guidelines to learn more about these features.

Bug FixesN/A
Known Issues
  • Standalone Bootloader & OTA Client
    • Currently supporting standalone (as opposed to application) bootloader
    • OTA Server functionality supported
      • OTA Server functionality supported
  • Green Power Support
    • Green Power as a Proxy not supported (required for zb 3.0 compliance)
  • Basic Cluster Attributes
    • Still under investigation is a possible issue with local attribute writes to the Basic cluster, which require a reset of the device
    • For the time being it is advised that Basic cluster attributes not be adjusted locally

Files:

EFR32MG1 Solution (BSB03PA1x modules):

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware Image

RapidConnect_3_0_1.gbl

EM357 Solution (Z357PA4x modules):

OTA Upgrade Firmware ImageN/A
Serial Upgrade Firmware Image

RapidConnect_3_0_1.mbl

Serial Protocol Specification:

You can find our RapidConnect Serial Protocol v3.0 here.

Note: see the License Agreements page for the terms and conditions that apply to the use of MMB's RapidConnect products.

  • No labels

Legal Notices

Copyright © 2020 MMB Networks, Inc. All rights reserved.
Confidential materials prepared and delivered by MMB Networks for receipt and review only by any partner subject to a valid and enforceable MMB Networks confidentiality agreement. Any receipt, review, or misuse of any of the content exchanged hereunder by any party not a party to this confidential exchange shall be subject to any and all rights available under the law. All rights, title and interest to the materials shall remain with MMB Networks.
Any suggestions provided to MMB Networks with respect to MMB Networks' products or services shall be collectively deemed “Feedback.” You, on behalf of yourself, or if you are providing Feedback on behalf of your employer or another entity, represent and warrant that you have full legal authority to bind such entity to these terms, agree to grant and hereby grant to MMB Networks a nonexclusive, perpetual, irrevocable, royalty free, worldwide license to use and otherwise exploit such Feedback within any MMB Networks products and services.